We Now Accept KLARNA

WE SHIP WORLDWIDE!

My Cart

PEC Steel Connecting Rods

£600.00
Qty Available: 2
In stock
Only 2 left
Pay In 3 interest-free payments of £240.00


More Information
Car Model Toyota Celica ST165
Toyota Celica ST185
Toyota Celica ST205
Toyota Caldina ST215
Toyota Caldina ST246
Toyota MR2 SW20 NA
Toyota MR2T SW20 Rev1/2
Toyota MR2T SW20 Rev3>
Description Sold as a set of 4

PEC's own in house design facilities are able to create many different components but for nearly 10 years now
it's our connecting rods that have helped set us apart from the competition in terms of availability
ease of fitment and size of range.

Manufactured from forgings originally produced in Sweden
PEC connecting rods have offered engine builders and tuners a cost efficient and yet high performing solution to a wide variety engine building problems.

H-Beam and I-Beam section connecting rods are forged from AISI 4340 (En24) steel. Heat treated to HRC 35-38 and then shot peened for a higher fatigue strength. Small ends are bushed for a fully floating pin and big ends are fitted with high quality ARP fasteners with different specification bolts available depending on the level of performance required.

PEC Connecting rods have been designed
manufactured and tested to the highest levels of scrutiny before being released to the trade and the public alike and their success record speaks for itself.

PEC rods are designed to withstand roughly 225hp per cylinder (typically 900hp on most 4cyl engines) and on the ARP 2000 series 3/8 bolts normally provided & have an 8,500 RPM safe operating limit (engine specific).

In some cases
we reccomend using the ARP custom age bolts available from us. This increases the hp threshold to 250hp per cylinder and raises the RPM limit to 9,000 however as every engine is different
these numbers are not guaranteed for every configuration.

Prolonged high RPM's for drifting
or sudden bursts of torque for drag racing (as two examples) will warrant the use of the custom age bolts to help retain the clamping force between the big end cap and the connecting rod.

Specifiction:

Part Number G0051

Engine Type 3SGTE / 3SGE / 3SG / 2.0 16v

Length C/C 138.00mm

Small End Diameter 22.00mm

Small End Width 26.75mm

Big End Diameter 51.00mm

Big End Width 26.75mm

Generic picture used.

Short Description G0051
Write Your Own Review
You're reviewing:PEC Steel Connecting Rods
Short Descrption
G0051

Descrption
Sold as a set of 4

PEC's own in house design facilities are able to create many different components but for nearly 10 years now, it's our connecting rods that have helped set us apart from the competition in terms of availability, ease of fitment and size of range.

Manufactured from forgings originally produced in Sweden, PEC connecting rods have offered engine builders and tuners a cost efficient and yet high performing solution to a wide variety engine building problems.

H-Beam and I-Beam section connecting rods are forged from AISI 4340 (En24) steel. Heat treated to HRC 35-38 and then shot peened for a higher fatigue strength. Small ends are bushed for a fully floating pin and big ends are fitted with high quality ARP fasteners with different specification bolts available depending on the level of performance required.

PEC Connecting rods have been designed, manufactured and tested to the highest levels of scrutiny before being released to the trade and the public alike and their success record speaks for itself.

PEC rods are designed to withstand roughly 225hp per cylinder (typically 900hp on most 4cyl engines) and on the ARP 2000 series 3/8 bolts normally provided & have an 8,500 RPM safe operating limit (engine specific).

In some cases, we reccomend using the ARP custom age bolts available from us. This increases the hp threshold to 250hp per cylinder and raises the RPM limit to 9,000 however as every engine is different, these numbers are not guaranteed for every configuration.

Prolonged high RPM's for drifting, or sudden bursts of torque for drag racing (as two examples) will warrant the use of the custom age bolts to help retain the clamping force between the big end cap and the connecting rod.

Specifiction:

Part Number G0051

Engine Type 3SGTE / 3SGE / 3SG / 2.0 16v

Length C/C 138.00mm

Small End Diameter 22.00mm

Small End Width 26.75mm

Big End Diameter 51.00mm

Big End Width 26.75mm

Generic picture used.

Please click Compatibility Tab to see which vehicles this part fits

We found other products you might like!